Rescue Tool System Specifications for Vernon Parish Fire District
Vernon Parish Police Jury
Sealed Bid: 36519121
Listing Information/Advertisement
RESCUE TOOL SYSTEM SPECIFICATIONS
The equipment specified in this bid must all be designed and warranted for use on the
Hurst JAWS OF LIFE rescue tool systems- no exceptions. All of the tools and other equipment
must be designed and warranted to work with and be interchangeable with the existing Hurst
tools in use by the Fort Polk, DeRidder, and Sandy Hill fire departments. If bidding other than
specified brand, bidders must enclose with their bid two (2) copies of detailed manufacturer's
specifications on the product bid including a complete list of any deviations from the
specifications listed. Standard sales brochures are not acceptable.
All hoses must be labeled for use on Hurst JAWS OF LIFE rescue systems. The hoses
must be non-perforated, electrically non-conductive with a pressure rating of20,000 psi. and
have a 4:1 safety factor based on a maximum operating pressure of 5,000 psi. Hoses will be a
twinned designed and bright orange, green, or blue in color for high visibility ..
For the safety oftool operators and victims all of the equipment will operate using Hurst
fire resistant, non-conductive, synthetic, non-evaporating synthetic hydraulic fluid.
Comply:__ Exception: __
Tools and components must be NFP A 1936 compliant and UL listed. Each tool, power unit,
and hose shall have a label denoting compliance. The manufacturer of the hydraulic tools shall
be ISO 9001 and 14001 certified.
Comply:__ Exception: __
Streamline single line fittings:(p/n: 128RI07, 128RI08)
* All tools and hoses will be equipped with Streamline fittings.
* Fittings must be able to disconnect and connect under pressure.
* Fittings must be able to retro-fit any Hurst tool.
Comply:__ Exception: __
2 ea. model JL-4GH-SI dual pump simo mounted power units: (pin: 363R308)
* Unit to have Honda 5.5 hp 4 cycle engine and dual independent pumps.
* Unit to have a reservoir capacity of no less than 2.1 gallons (8 liters).
* Unit must be able to operate two tools simultaneously and independently with full
pressure and flow.
* There will be two separate dump valves each with its own Streamline fittings for
connection of extension hoses.
* Pump will shift from low pressure stage at 2000 psi. for faster operation.
* Unit will have tubular steel roll cage surrounding pump and engine.
* Dimensions are 19 in., 17 in., 20 in., and have a max. weight of 87 lb.
* Unit to include and operate on Hurst synthetic hydraulic fluid and be able to operate all Hurst
rescue tools.
Comply:__ Exception: __
4 ea. model JL-ER hydraulic hose reels (pin: 542R077-orange hose, 542R079-blue hose):
* Reels will come complete with 100 feet of Hurst twin lined non-conductive hydraulic hose.
J
*Hoses to have Hurst Streamline fittings for fast connection to tools and hoses.
*The reels to be specifically designed and warranted for its intended use with Hurst rescue tools.
* The hose is to be rewound by electric motor. The motor shall run from a 12 volt power source
and not draw more than 25 amps. The motor and drive will be enclosed within the frame.
* Reels to free standing unit and not permanently attached to the power unit.
* Reels to be supplied with 2 ea. jumper hoses to connect to power unit (2 ea. 6 ft. length).
Jumper hoses to have Hurst Streamline fittings on both ends for fast connection.
* Connections to the reels are to be same quick disconnects as on the tools.
* For long life and damage resistance the drum panels and frame side walls are to be made of
stainless steel.
* Maximum dimensions of reel to be 14.79 in. long, 14.46 in. wide, 18 in. high and weigh 541bs.
* Reel frame to have four holes on base to allow reel to be bolted to vehicle.
*Reels to be delivered full of Hurst hydraulic fluid and be ready for use.
Reel hose specifications:
* Kevlar reinforced, thermoplastic construction. Steel braided hose is not acceptable.
* Electrically non-conductive, non-perforated and meets or exceeds SAE 100R8 standard.
* Streamline fittings installed on each hose.
* Hose must be labeled and warranted for use on Hurst JAWS OF LIFE rescue tools.
* Hose must have a pressure rating of 20,000 psi. and be twinned design.
* Hose must be bright colored for high visibility.
Comply:__ Exception: __
2 ea. Model JL-MOC-ULTRA Heavy Rescue Cutters: (pin: 362R488)
* Cutting force- 195,126 lbs.
* Cutter blade opening- 5.2 in.
* Operating mechanism must be star grip to allow operation from any position.
* Star grip mechanism to be "dead man" type valve where tool stops when released.
* Twist grip (motorcycle style) control mechanism will not be accepted.
* Star grip must be separate and independent from rear handle.
* Handle designed to hold hoses and direct them away from work area.
* Tool weight- 46 lbs.
* Tool must be able to operate from all Hurst 5000 psi power units.
Comply:__ Exception:_. _
2 ea. ML-28 Defender spreaders (pin: 362R471):
* Tool to have spreading distance of28 inches. -
* Tool to have spreading force of 44,000 lbs.
* Tool to have pulling force of 20,000 lbs.
* Weight not to exceed 48 lbs.
*Operating mechanism to be star grip to be "dead man" type whereby tool stops when released.
Star grip allows operation from any angle. Twist grip (motorcycle style) are not acceptable
because they are exposed and can become stuck during rescue operations.
* Star grip must be separate and independent from rear handle.
*Jaw tips are to be field removable for service and cleaning.
* Jaw tips will have holes for attachment of chain shackles and attachments.
* Tool will be designed and warranted to operate from all Hurst power units.
Comply:_._ Exception: __
2 ea. Mini-mate ML-4G-SI compact portable power units: (pin: 363R302):
* Unit to have 3 hp Honda 4 cycle engine.
* Two stage 10,000 psi pump set to operate at 5000 psi for long life. Pump shift point to be 2000
pSI.
* Unit must be able to operate two tools independently at full pressure.
* Fluid capacity: .92 gallons.
* Dimensions: 18"xI2"xI7.5"; weight: 60 lbs.
* There will be two separate dump valves each with its own set of Streamline fittings for
connecting extension hoses.
Comply: __ Exception: __
4 ea. Hydraulic hoses - 30 ft. length: (2 ea. pin: 353R324, 2 ea. pin: 353R326):
* Kevlar reinforced, thermoplastic construction. Steel braided hose is not acceptable.
* Electrically non-conductive, non-perforated and meets or exceeds SAE 100R8 standard.
* Hoses must be equipped with Streamline fittings.
* Hose must be labeled and warranted for use on Hurst JAWS OF LIFE rescue tools.
* Hose must have a pressure rating of 20,000 psi. and be twinned design.
* Hose must be bright colored for high visibility.
Comply:__ Exception: __
2 ea. model JL-20C rams: (PIn: 257R151)
* Opening force - 15,000 lbs.
* Length closed - 15 in.
* Length extended - 22 in.
* Ram to have hole for attaching accessory tips using quick release pins.
* Ram to have "dead man" valve whereby tool stops when valve is released.
* Ram to be equipped with dual pilot check valve for maximum load holding ability.
Comply:__ Exception: __
2 ea. Model JL-30C rams: (pin: 257R152)
* Opening force - 15,000 lbs.
* Pulling force - 6,000lbs.
* Length closed - 23 in.
* Length extended - 36 in.
* Ram to have holes for attaching accessory tips, extensions, and chains using quick release pins.
* Ram to have "dead man" valve that makes tool stop when valve is released.
*Ram to be equipped with dual pilot check valve for maximum load holding ability.
Comply: __ Exception: __
2 ea. Streamline adapter sets: (pin: 101R7374)
* Set to include 1 ea. Streamline 128RI08 to 1280008 adapter and 1 ea. Streamline
128RI07 to 128008 adapter.
* Set to allow fast connection of Streamline tools and hoses to standard connectors.
Comply: __ Exception: __
2 ea. Ram Extension sets (pIn: 10IR038-22)
* Set to consist of three extensions, three attachment pins, and carrying case.
* Extensions are to be ofthree lengths and increase over all length of ram by 6 in., 10 in., and 15
in. All extensions will be 2.85 in. width and height.
* Extensions bodies will be made of 6061- T6 aluminum with heat treated investment cast SAE
4140 steel plate end plates.
* Extensions will attach to ram using steel pins with rings and stops through the holes on the
ram.
* Extensions will be designed and warranted to fit Hurst JL-20B,C, JL-30A,B,C and JL-60A,B,C
rams.
* Also to include 1 ea. pIn: 347R023 base plate, 1 ea. pIn: 347R024 "V" block and 2 ea. pIn:
1890018 shackle pins.
2 ea. Ram I spreader attachment sets (pIn: 257R037) consisting of:
* 1 ea. base plate,
* 1 ea. "V" adapter,
* 1 ea. piercing point
* 1 ea. cutting wedge,
* 2 ea. quick release pins,
*1 ea. spreader adapter,
* 1 ea. carrying case.
2 ea. Quick Kick ram supports: (pIn: 247R028)
*Adjusts to fit different size rocker panels.
*Provide a secure starting for base of any ram.
Comp1y:__ Exception: __
2 ea. air lifting bags sets: (pIn: 310R040)
*Set includes: 1 ea. V-40, 1 ea. V-24, 1 ea. V-I0 bag, 1 ea. Control console pin: 409R002, 2 ea.
air hoses with shut off I relief valves, 1 ea. hose storage bag.
Comply: __ Exception: __
2 ea. Quick Strut stabilization sets: (pIn: 362A491)
*Set includes 2 ea. struts adjustable from 48" to 78",2 ea. crank handles, 1 ea. carrying case.
*Lifting force of each strut: 2205 1bs.
*Tota1 weight of set: 75 lbs.
Comply: __ Exception: __
Hurst rescue tool warranty and training:
* All tools will have a two-year parts and labor warranty.
* All tools will have tags attached indicating NFP A 1936 compliance.
* All tools will be warranted as RESCUE TOOLS specifically for the purpose for which
they have been designed.
* Factory warranty must be supplied with bid.
* A complete training class will be conducted for the department at their location.
* Training will be provided by a Hurst certified instructor.
* Training to be provided at no charge with refresher classes available as needed.
* Training will cover vehicle rescue and extrication techniques, safety procedures, and
operation and care of the tools.
* Training will be eligible for EMT continuing education credit and meet NFPA 1670
objectives.
* All tools and equipment must be delivered completely set up and operational.
* Repairs and service of equipment will be performed by a Hurst factory authorized service
center on site at the fire department.
* Loaner tools will be supplied at no charge if any tools are removed from service for repairs,
even after the warranty period ends.
Comply:__ Exception: __

Additional Notes/Requirements
Bids must be honored for 12 months. All exceptions to specifications must be listed and detailed here:
BID SUBMITTAL INFORMATION
Creator Username: vppj
Bidding Privacy: Bid encryption
Started: 18-Feb-2010 01:43:31 PM
Ends: 24-Mar-2010 02:00:00 PM ( Expired )
History: 1999 Views, 0 Questions
Event Status: Expired since 24-Mar-2010 02:00:00 PM
Actions: Sign-In to Bid
Username:

Password:
Visitors: Visitors/Central Bidding Plan Holders
DOWNLOAD BID DOCUMENTS
PUBLIC MESSAGE BOARD
Discuss questions with the owner/creator of this Listing.
UPDATE/ADDENDUM HISTORY
All updates/changes are listed below::
 
BID HISTORY
Username Bid Amount Type Company name Bid Amount Bid Placed
-- No Results Found --
Bids Added by Agency/Owner
Username Bid Amount Type Company name Bid Amount Bid Placed